Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
Write the flowchart and program to output the triangle wave by counting from OOH to FFH and then back down to OOH again and repeating this pattern and outputting this to Port-I which has a DAC conne
The demand placed on the system is described by a log normally distributed random variable with mean 50 and standard deviation of 10. Capacity of a system is modelled by a Weibull random variable w
The zero up-crossing method is the most common method for analysing a waverecord in the time domain. In shallow water, at the point when the crest particle velocity becomes greater than the wave cel
If the forecast for January was 25, determine the forecast for sales for the months February through September using an exponential smoothing method with α = 0.30. Also compute the mean square
Calculate the total drill and blast cost based on the following blasting costs:Explosives $550.00/tonne, Blast initiation $11.30/blasthole, Blast labour $80.00/tonne of explosive.
A diluted polymer solution with a density of 1130 kg/m3 was extruded through a capillary tube of 3.5 mm internal diameter and 1 m long. The following results were obtained at 25°C. Estimate the
Understand the nature and use of present health and safety legislation.Identify all the UK legislation, regulations and relevant codes of practice which must be complied with to ensure the safety of
Calculate the CO emission rate from the stove.
The tunnel is to have a circular horizontal alignment turning right from the crosscut with aradius of not more than 50m and not less that 30m with a maximum grade of 1 in 10.Compute the co-ordinates
The goal is to simulate a real life product development and familiarize students with the design process of a system, component, or process to meet desired needs within realistic constraints such as
Taking π = 3.142, calculate the Fourier cosine series approximation of f(t), up to the 6th harmonics when t = 0.79.
Draw a schematic diagram below of the major parts of the SEM: filament, Wehnelt, anode, condenser lens, condenser aperture, objective lens objective aperture, and scanning coils. Explain briefly the
Evaluate and Investigate different Gas Turbine Engine configurations in use for commercial or military Gas Turbine Engine aircraft.
Formulate the problem as stochastic dynamic programming problem. Specify phases, states, decisions and the optimal value function. Draw the decision tree for this problem.
As a forensic materials expert – you have been asked to recognize a metallic powder found on the clothing of someone suspected of fabricating an incendiary device used in an armed robbery.
A water treatment plant uses a dual media filter. The two media employed.
How long it would be before each year's deposit of refuse is saturated and leach ate flows from that section? Use rainfall and evapo-transpiration values appropriate for your area.
Can a web base EOC be a way for Cheyenne County to meet its coordination and communications requirements? What factors work in favour of a web solution, and what factors are opposed?
An asymmetric, multimode, step-profile slab waveguide has a core index of 1.49. The cladding index above the core has value 1.47.
Researched paper on one of the above subjects, showing its history, internal components, full operation, advantages and disadvantages over other transmissions.
Using the rat stereotaxic atlas in the course materials, devise a surgical plan for implanting a Michigan type array (Neuronexus) of 16 electrodes into the VL thalamus.
Compare your outcomes from parts a, b, and c above with the NACA 4412 experimental data and express the percentage difference between your outcomes and experiment.
Describe the general “four digit” system of designating aluminum alloys including modifiersThere are two types of aluminium alloy: 2024-T4 and 6061-T6511. Explain fully the meaning of th
Solve the problem using the MIP method and report the flow-distance score of the layout. There are no building restrictions.
Explain the process and establish contractual needs for MLDT and MADT. Use sketches and computations to justify your required values.