• Q : Floating point numbers-ieee standard....
    Electrical Engineering :

    Describe how various instruction are executed in computer with diagram of instruction cycles?

  • Q : Broad side array and end fire array....
    Electrical Engineering :

    What do you mean by the term linear array? Compare Broad side array and End fire array?

  • Q : Antennas and wave propagation....
    Electrical Engineering :

    What are the different merits and demerits of loop antennas?

  • Q : Transfer function for armature....
    Electrical Engineering :

    Derive the Transfer Function for armature controlled d.c. motor, with neat diagram and describe the benefits of armature controlled d.c. motor over field controlled d.c. motor.

  • Q : Control system using open loop and closed loop system....
    Electrical Engineering :

    Describe the temperature control system concepts by using open loop as well as closed loop system.

  • Q : Principle of heterodyne wave analyzer....
    Electrical Engineering :

    Explain the principle of heterodyne wave analyzer with a block diagram.

  • Q : Basics of circuit instrumentation....
    Electrical Engineering :

    Draw the circuit of an electronic dc voltmeter and explain its working principle. What are the draw backs of it and suggest a method to offset these problems.

  • Q : Electronic measurements and instrumentation....
    Electrical Engineering :

    Draw the schematic comprising values for an Ayrton shunt for a meter movement having a full scale deflection of 1 mA and an internal resistance of 500 Ω to cover the current ranges of 10, 50,

  • Q : Independent and dependent sources....
    Electrical Engineering :

    Describe the independent and dependent sources with the help of V-I characteristics.

  • Q : Basics of half wave rectifier....
    Electrical Engineering :

    Draw the circuit of a half-wave-rectifier and find the ripple factor, % regulation, efficiency and PIV.

  • Q : Forward bias and reverse bias....
    Electrical Engineering :

    Describe the operation of silicon p-n junction diode and obtain the forward bias and reverse bias Volt-Ampere characteristics.

  • Q : Fundamentals of semi-conductors....
    Electrical Engineering :

    What do you mean by Fermi level? By indicating the position of Fermi level in intrinsic, n-type and p- type semiconductor, describe its significance in semiconductors?

  • Q : Determining maximum power transfer....
    Electrical Engineering :

    Find out the load resistance to receive maximum power from the source, also find out the maximum power delivered to the load in the circuit as shown below.

  • Q : Solving network circuits....
    Electrical Engineering :

    A pure inductance of 3 mH carries a current of the wave form shown in figure. Find out the voltage across Inductor VL(t) and sketch the same.

  • Q : Applications of bernoullis energy theorem....
    Mechanical Engineering :

    Mention any eight practical applications of Bernoulli`s energy theorem.

  • Q : Newtons law of viscosity....
    Mechanical Engineering :

    State Newton's law of viscosity and give any four examples of its applications.

  • Q : Working principle of bourdon pressure gauge....
    Civil Engineering :

    Describe the working principle of Bourdon pressure gauge with the help of a neat sketch.

  • Q : Fundamentals of fluid mechanics....
    Mechanical Engineering :

    The pressure inside a droplet of water is 0.04N/cm2 greater than the atmospheric pressure. Calculate the diameter of the droplet. Take surface tension (water with air) = 81N/m.

  • Q : Concrete technology....
    Civil Engineering :

    What are pozzolonas? Describe the pozzolonic reactions in concrete? List out the common pozzolona used in concrete?

  • Q : Plastic moment capacity....
    Civil Engineering :

    Determine the plastic moment capacity of a continuous beam shown in figure below:

  • Q : Structural analysis-analyzing portal frame....
    Civil Engineering :

    Analyze the portal frame shown in figure below by moment distribution method. All the members have same flexural rigidity. The member BC carries a uniformly distributed load of 15 kN/m.

  • Q : Importance of geology in the fields of metallurgy....
    Civil Engineering :

    Give a brief account of applied importance of Geology in the fields of metallurgy, mining, ground water investigation etc, apart from civil engineering.

  • Q : Groundwater management and development....
    Civil Engineering :

    List out various methods for determination of permeability and describe any one in detail all along with a neat sketch.

  • Q : Remote sensing and gis applications....
    Civil Engineering :

    a) Describe the electromagnetic process in integration with GIS. b) Describe the electromagnetic energy interactions with earth surface materials.

  • Q : Report on hazardous and toxic waste....
    Civil Engineering :

    Hazardous and toxic waste: how are they treated, regulations in USA about hazardous waste, safety measures, pollution problems (real case studies), remediation technologies.

©TutorsGlobe All rights reserved 2022-2023.