• Q : Circuit and correct what is wrong....
    Electrical Engineering :

    I am doing a simulation using Matlab /Simulink and the circuit (based on power electronic components) is not working as it has to. Does any one can review my circuit and correct what is wrong in

  • Q : Determine the angular velocity of links ab and bc....
    Mechanical Engineering :

    At a given instant in time, flywheel OA is caused to rotate with angular velocity of w=2rad/sec and angular acceleration o alpha=6rad/s2. Determine the angular velocity of links AB and BC at this inst

  • Q : Consider a sinusoidal wave with frequency....
    Electrical Engineering :

    Consider a sinusoidal wave with frequency of 300KHz as a carrier signal. We want to transmit a sinusoidal signal with f=3KHz and Amplitude=1. Plot the AM modulated signal in MATLAB.

  • Q : Calculate the entropy change for the ensuing process....
    Mechanical Engineering :

    Calculate the enthalpy, entropy, and gibbs free energy changes when 10g of supercooled liquid silver solidifies isothermally at 1133K and 1atm. Show that the second law is obeyed.

  • Q : Realize the storage circuits....
    Electrical Engineering :

    The block diagram for an elevator controller for a two-floor elevator follows. The inputs FB1 and FB2 are 1 when someone in the elevator presses the first or second floor buttons, respectively. Th

  • Q : Minimum work with which this process could be accomplish....
    Mechanical Engineering :

    An insulated piston-cylinder device contains 2L of saturated liquid water at a pressure of 150kPa-which is constant throughout the process.

  • Q : The closed limb of a macleod gauge....
    Electrical Engineering :

    The closed limb of a macleod gauge has a diameter of 1mm and a value V above the level of the opening W of 250cm3. When the gauge is connected to a vacuum source the difference h in mercury leve

  • Q : What must be the diameter to allow an elongation....
    Mechanical Engineering :

    A cylindrical rod of steel (E = 30 x 106 psi)having a yield strength of 45,000 psi is to be subjected to a load of 2,500 lbf. If the length of the rod is 20.0 in., what must be the diameter

  • Q : Design a negative edge-triggered....
    Electrical Engineering :

    Design a negative edge-triggered D flip-flop that uses three SR latches constructed with cross-coupled NOR gates. Also connect asynchronous inputs Preset (PST) and Reset (RST). Draw the logic di

  • Q : The average source and destination....
    Electrical Engineering :

    For a 1-Gbps network operating over 5000 km, the delay is the limiting factor, not the bandwidth. Consider a Metropolitan Area Network (MAN) with the average source and destination 40 km apart. At

  • Q : What is the full load for secondary....
    Electrical Engineering :

    A 300-kilowatt-ampere transformer bank consisting of three 100-kilovolt-ampere transformer has a 3-phase, 480-volt delta primaryand a 3-phase, 208Y/120 secondary. what is the full load for primar

  • Q : A block and tackle system....
    Electrical Engineering :

    A block and tackle system with nine supporting strands is used to lift a metal lathe in a manufacturing facility. The motor being used to wind the cable in the pulley system can provide 100 lb

  • Q : Determine the overall efficiency of the pump motor unit....
    Mechanical Engineering :

    Water is pump from a lake to a storage tank at 18m above at a rate of 70 L/s while consuming 20.4 kW of electric power. disregarding any frictional losses in the pipes and any change s in kinetic ener

  • Q : Determine the mass flow rate of steam....
    Mechanical Engineering :

    Steam enters a diffuser at 20 psia and 240oF with a velocity of 900 ft/s and exits as saturated vapor at 240oF and 100 ft/s. The exit area of the diffuser is 1 ft2. 

  • Q : A tile iron consists of a massive plate maintained....
    Mechanical Engineering :

    A tile-iron consists of a massive plate maintained at 150°C by an embedded electrical heater. The iron is placed in contact with a tile to soften the adhesive, allowing the tile to be easily

  • Q : Calculate the comprehensive stress developed in each slab....
    Mechanical Engineering :

    A large number of concrete slabs (each 0.6 m in length) are lined up with a spacing of 0.1 mm between them. The temperature is then increased by 50 °C.

  • Q : A metal processing facility....
    Electrical Engineering :

    In a metal processing facility, the final tailings slurry produced by the process is thicken in a caisson and thickener and pumped out of for disposal. The density of the slurry that leaves the t

  • Q : Calculate the mean velocity of the water....
    Mechanical Engineering :

    Given the absolute roughness of the pipe is 0.26 mm, density of water is 998 kg/m3 and dynamic viscosity of water is 1.14 × 10-3 kgm 1s-1.

  • Q : A conducting rod having a mass density....
    Electrical Engineering :

    A conducting rod having a mass density 2 kg/m is suspended by two flexible wires in a uniform magnetic field which points out of the page. a battery is also attached .if the tension on the wires

  • Q : How many bits are required to represent....
    Electrical Engineering :

    How many bits are required to represent the decimal numbers in the range from 0 to 999 using straight binary code? Using BCD code?

  • Q : The name of the free internet browser....
    Electrical Engineering :

    The name of the free Internet browser from Mozilla is:Podcasts use which of the following technologies The text version of a Web site's Internet address is called the:All of the following are ways to

  • Q : What is the maximum possible swath width....
    Mechanical Engineering :

    A remote sensing satellite is deployed in a circular sun-synchronous orbit with inclination 96.85°. A. Calculate orbit altitude (disregard gravitational pull by the Moon and Sun).

  • Q : What is the enthalpy of this reaction....
    Mechanical Engineering :

    A total of 2.00 mol of a compound is allowed to react in a foam coffee cup that contains 138 g of water. The reaction caused the temperature of the water to rise from 21.0 to 24.7 C.

  • Q : Calculate the tension in each cable when the trough is fill....
    Mechanical Engineering :

    The two sides of a V-shaped water trough are hinged to each other at the bottom where they meet, as shown in Figure Q1 , making an angle of 45° with the ground from both sides.

  • Q : An astronaut drops an object....
    Electrical Engineering :

    An astronaut drops an object from rest (relative to the planet) on a planet alpha (having the same radius as of earth) from an altitude of one radius above the surface. When the object hits the

©TutorsGlobe All rights reserved 2022-2023.