• Q : Voltage of the system....
    Electrical Engineering :

    Where I need to create a simulink file for buck converter which has a digital controller and feedback where it has digitization of output voltage of the system. So I just have question for mater

  • Q : Quisiera sabes cual es la amplitud del voltaje....
    Electrical Engineering :

    Quisiera sabes cual es la amplitud del voltaje de ripple pico a pico en la salida, cuando tengo una fuente de corriente continua sumada a una tension de ripple de entrada?

  • Q : Given the vector field....
    Electrical Engineering :

    Given the vector field, G = 2x²y ax - 2(z-x) ay + 3xyz az, find (a) G at P(2,-3,4); (b) a unit vecotr in the direction of G at P; (c) the (scalar) equation of the surface on which |G| = 100

  • Q : Create a student class with instance variables....
    Electrical Engineering :

    Create a Student class with instance variables for a gpa and a first and last name. Include a constructor that initializes a student with their name. Also include a method to update the gpa by

  • Q : A perfectly conducting plane is located....
    Electrical Engineering :

    A perfectly conducting plane is located in free space at x=4,and a uniform line charge of 40 nC/m lies along the line x=6,y=3.Let V=0 at the conducting plane.At P(7,-1,5) find Voltage and Electr

  • Q : You want to send music to the dorms....
    Electrical Engineering :

    you want to send music to the dorms with 15 kHz of AM modulation frequency on a carrier of 1090 kHz.If the carrier amplitude in the transmitter (before the power amplifier at the output) is 5 V, wha

  • Q : The runner-up in a road race]....
    Electrical Engineering :

    The runner-up in a road race is given a reward that depends on the difference between his time and the winner's time. He is given 20 dollars for being one minute behind.

  • Q : A resistance coil....
    Electrical Engineering :

    A resistance coil AB of 100 Ω resistance is to be used as a potentiometer and is connected to a supply at 230 V. Find, by calculation, the position of a tapping point C between A and B suc

  • Q : A modern transmits....
    Electrical Engineering :

    A modern transmits a 2 voltage signal into a channel. the channel adds to this signal a noise term that is drawn from the set {0,-1,-2,-3} with respective probablities {4/10, 3/10, 2/10, 1/10},

  • Q : Noninverting-input voltage....
    Electrical Engineering :

    With its noninverting-input voltage at 10uV, the output voltage of an op amp is -15V. If A = 5*10^5 and V_CC = 15V, can you determine the magnitude of the inverting-input voltage? If not, can you

  • Q : Employment response to competition....
    Electrical Engineering :

    Do you agree with IBMs employment response to competition from software development contractors in India, like Wipro , that are expanding into It consulting services? why or why not?

  • Q : Two factory produces identical clock....
    Electrical Engineering :

    Two factory produces identical clock production of first factory consist 10000 clock in which 100 are defective , the second factory produces 28000 clock in which 30 are defective what is the pr

  • Q : The signal to interference ratio....
    Electrical Engineering :

    You are asked to determine the signal-to-interference ratio (SIR or C/I) on the forward link of a cellular system, when the mobile is located on the fringe of its serving cell. Assume that all ce

  • Q : A unit all for uranium has orthorombic symmetry....
    Electrical Engineering :

    A unit all for uranium has orthorombic symmetry with a,b, and c lattice parameters of 0.286, 0.587, and 0.495 nm. respectively. if its density,atomic weight and atomic radius are 19.05 g 238.03

  • Q : Three single phase two winding transformers....
    Electrical Engineering :

    Three single phase two winding transformers, each rated 400MVA, 13.8/199.2kV, with leakage reactance Xeq=0.10PU, are connected to form a three phase bank. The high voltage windings are connected

  • Q : Create a circuit of three level-sensitive....
    Electrical Engineering :

    Create a circuit of three level-sensitive D latches connected in series (the output of one is connected to the input of the next). Use a timing diagram to show how a clock with a long high-time

  • Q : The eletric field intensisty in zero....
    Electrical Engineering :

    A point electric charge of 8Nc in kept at a distance of 1m from another point charge of -4Nc in free space. determine the location of a point along the line joining two charges where in the eletr

  • Q : A single-turn square loop of wire....
    Electrical Engineering :

    A single-turn square loop of wire, 2.00 cm on each edge, carries a clockwise current of 0.200 A. The loop is inside a solenoid, with the plane of the loop perpendicular to the magnetic field of the

  • Q : The wire length scales inversely proportiona....
    Electrical Engineering :

    Consider a CMOS inverter followed by a wire of length L. Assume that in the reference design, inverter and wire contribute equally to the total propagation delay tpref. You may assume that the trans

  • Q : What is the output variable....
    Electrical Engineering :

    A process with Gp= 2/(2s+1) and Gd=1/(2s+1) experiences a disturbance step change of magnitude 5. The SP remains constant. If a P-controller alone with Kc=1 is used and Ga=Gs=1, then what is the

  • Q : Calculate the voltage regulation of the line....
    Electrical Engineering :

    A three-phase, 60 Hz transmission line has the following parameters R = 0.25 Ohms/mi, X = 1.0 Ohms/mi, and Y = 5.0uS/mi. The line is 200 mi long and it delivers 150 MW at 220 kV and unity power f

  • Q : Solved java source code the size....
    Electrical Engineering :

    Solved java source code the size of the side of a square, then displays a hollow square of that size made of asterisks. Your program should work for squares of all side lengths between 1 and 20.

  • Q : Aluminium is a trivalent element....
    Electrical Engineering :

    Aluminium is a trivalent element with atomic weight of 27 gm/mole and density of 2.7*103 kg/m3, with a mean free time between electronic collissions of 4*10-14s. Calculate the current that flows

  • Q : A clean nickel surface is exposed....
    Electrical Engineering :

    A clean nickel surface is exposed to light of wavelength of 235nm. What is the maximum speed of the photoelectrons emitted from this surface. The work function for nickel is =5.1 eV. Answer: 2.5

  • Q : What would be the measured voltage....
    Electrical Engineering :

    In the circuit shown in Figure A-4, the zener diode is rated at 5.6 V and is operating in the zener region. If the voltage from the variable DC power source is 10 V, what would be the measured volt

©TutorsGlobe All rights reserved 2022-2023.