Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Active Tutors
Asked Questions
Answered Questions
Using Euler's relation , the signal x(t) defined above canbe expressed as a sun of complex exponential signals using the finite Fourier synthesis summation. Determine values for f, N and all the com
The voltage and current at the terminals of the circuit element are zero for t < 0. For t >= 0 they are v = (10,000t+ 5)e^-400t V. and i = (40t + 0.05)e^-400t A. a) at what instant of time is
In a CDMA system the chip duration is 0.26us and maximum excessdelay 1.3us, into how many delay bins do the multipath components fall if the maximum excess delay is 100ns is the CDMA system narrowba
The terminal voltage of the battery is v=11 +0.5t for t>0. a. Find the energy delivered to the battery during the five hours. b. If electrical energy costs 10 cents/k Wh, find the cost ofcharging t
Ten billion electrons per second pass through a particularcircuit element. What is the average current in that circuit element
The Source feed two loads, both of which areY-connected. The impedance of load 1 is 8 + j6 Ω/φ. Thecomplex power for the a-phase of load 2 is 600<36 ° VA.Find the total complex powe
A variable-speed motor having a nameplate rating of 15 hp, 890 r/min develops a torque of 25 newton meters at 1260 r/min. Calculate the per-unit values of the torque, speed, and power.
a line is 845miles in length. the line contains four conductors, each weighing 2526lb per 1000 ft. how many kilo grams of conductor are in the line
The load can be connected in either wye or delta configuration. Calculate the load power and apparent power when connected to a 208V 60Hz supply, with each of wye and delta connection.
A DC circuit has supply voltage 100V, impedance Z= 8+j6Ω. Calculate the stead DC current and power supplied to the circuit
A single phase AC circuit is conected to a 120V, 60Hz. The circuit impedance is Z=8+j6Ω at 60Hz. Calculate the rms phase current, real & reactive power and power factor.
The shunt capacitance of metal work ofeach insulator is 0.26C to earth and 0.15C to line. Find the stringefficiency if a guard ring increases the shunt capacitance to lineof the metal work of the lo
A single core cable for66kV three phase system has a conductor of 2 cm diameter and sheathof inside diameter of 5.3 cm. It is required to have twointer-sheaths so that stress varies between the same
Find the spacing between conductors of three phase transmission line with conductors of diameter 2.5 cm to avoid corona which will take place if the linevoltage exceeds 150kV (rms).
List the eight degenerate two-level forms and show that they reduceto a single operations. Explain how the degenerate two-level formscan be used to extend the number of inputs to a gate.
Determine the corona lossof a three phase, 220kV, 50 Hz and 200km long transmission line of three conductors each of radius 1 cm and spaced 5m apart inequilateral triangle formation. The air tempera
implement the following boolean function F, using two-level forms (a)NAND-AND, (b)AND-NOR,(c)OR-NAND,and(d)NOR-OR: F(A,B,C,D) = Σ(0,1,2,3,4,8,9,12)
Determine the impulse response and the unit step response of the system described by the difference equation. y(n) = 0.6y(n - 1) - 0.08y(n - 2) + x(n)
Implement the following function with a 4-to-1-line multiplexer Draw the truth table and the corresponding block diagramfor the MUX F(x,y, z) = f(1, 2, 6,7)
A 480 V, three phase system is supplying a 10kW heater and a 5kVAR cap bank. draw the power triangle and calculate the line current
A 100kW,230V,shunt generator has Ra=0.05ohm and Rt=57.5ohmassume that htere is negligible voltage drop across the brushes. ifthe generator operates at rated voltage, calculate the following: a) indu
a 3-phase slip ring induction motor gives a reading of 60volts,across a slip ring of open circuit. When at rest with normal statervoltage applied, the rotor is star connected and has an impedanceof
A permanent magnet motor is driving a load that requires 0.08Nm.The motor data is:RA =2W, VA =12v,Kt =0:05Nm/A ,KG = 0:004 V/RPM . Find themotors running speed and the power output.
A permanent magnet generator has Kt = 0:02Nm/A . The terminal voltage is six volts. It is spinning at 2500 rpm. It is connected to a load with a resistance of 30W. Determine the counter torque and t
At a design review for your first engineering project, you presentthe project to a panel of three senior engineers who will vote onwhether your project should be funded or not. The senior engineersw