Start Discovering Solved Questions and Your Course Assignments
TextBooks Included
Solved Assignments
Asked Questions
Answered Questions
(a)Write out the channel matrix P and sketch its model formed by 2 identical parallel binary system channels(assume X-over prob is pdash) (b)Find the channel capacity C and the input probabilty that
Design a power system for a facility, which requires both three phase and single phase supplies. Following conditions must be applied in the design: 1) The facility is at least 60 km far from a dist
1-If the AB current in a Y-connected load has an angle of -14°, what is the angle of the a-phase current. (0 decimals in degrees) 2-If the current of the a-phase in a Y-connected load has an angl
Let x(t) = |cos120pit| a periodic signal. Plot x(t). What is the period and frequency of x(t). Expand x(t) in trigonometric Fourier series Hint: use the plot to find the Fourier coefficients.
What is the primary source of distortion with a Class B amplifier. What are some ways the distortion can be minimized and discuss the tradeoffs that exist when implementing these distortion minimizi
There are 5 inductors in series and they are 1H,2H,3H,4H,5H what is the total equivalent inductance. There are 5 capacitors in series and they are 1F,2F,3F,4F,5F. what is the total equivalent capacita
(1) What happens if we connect an integrator and a diffetentiator together in series. What do we get. 2) Explain what is meant by 1nV/rtHz. What is the meaning of this specification.
Filament 1 is on the left, filament 2 is in the middle, and filament 3 is on the right. Filaments 1 and 2 have currents of 1 A in the ba z direction, and filament 3 has a current of 2 A in the ba z
a. A load consumes 150kW with a power factor pf = 0.7 (lagging). If the load current is 240A (RMS), find the load voltage. b. An industrial plant has an inductive load which consumes 10kW of powe
We have v1(t)=10cos(wt+30degrees). The current i1(t) has an rms value of 5A and leads v1(t) by 20s. (The current and the voltage have the same frequency) Draw a phasor diagram showing the phasors.
What is the nature of the process fluid and what are the objectives of the two sample points and in what way do the samples reaching the instruments differ?
Compare the differences in the FFT result. Explain why even though the inputs to both FFTs are the same cosine waves, the shapes of the FFTs are different. Calculate, plot and compare the results of
air expands through a nozzle at a rate of 1kg/sec. the outlet is at 15kpa and the inlet is at 400kpa,150degree and 35m/sec. assuming the process to be reversible and adiabatic, what is the exit velo
For the PMOS, calculate the applied voltage and the electric field (at the Si-SiO2 interface) to make the silicon surface intrinsic. What is the depletion width in this case.
a) Detrmine Frequency response of a 3rd order high-pass filter having a cutoff freq at 150hz. b) Detrmine freq response function of 4th order low-pass filter ahving cutoff freq at 600hz.
The output/ input of a system is 30dB. detrmine the ratio Express x(t)=4*cos(100*t-45)+ 2*cos(250*t+30) in terms of exponential functions Then Detrmine the phase angles(in degrees) of the two freque
The signal x(t)=10cos(t)+10sin(10t) is input into the following systems: a) \(H(s)=100/(s^{2}+10s+100)\) b) \(H(s)=s^{2}/(s^{2}+10s+100)\) calculate the output for each system.
design a sequential circuit that continuously computes the function 2X + 3 or 3X + 1 where the variable X is a three-bit unsigned integer available on a serial interface. A special external data sig
Using Floating Point Unit and the switch statement Create an HLA program to perform the following: -Two data conversions (decimal,binary,hex) -Two measurement calculations (miles,feet,meters,inches) -
Design a 3-bit counter using D flip-flops to cycle through the following sequence: 010, 101, 110,001. Make sure the counter is self-starting.
Write the full equations to light the bottom segment of a 7-segment display. INLCUDE the hexadecimal digits too ( b, c, d, and E ). Then simplify the equations using a k-map and draw the final circu
In a 120V compound generator, the resistances of the armature shunt and series windings are 0.06 ohm, 25 Ohm, and 0.04 Ohm respectively. The load current is 100A at 120V, find the induced EMF and th
A 25KW, 250V dc shunt generator has armature and field resistances of 0.06 ohm and 100 ohm respectively, determine the total armature power developed when working (1) as a generator delivering 25KW
when an AC source is connected accross a 12.0 resistor,the rms current in the resistor is 8.00 A find (a) the rms voltage accross the resistor,(b) the peak voltage of the source , (c) the maximum c
For PID control, what are roles of integral term and derivative term. Given KP=10, KI=3, and KD=4, write down this PID controller function.