• Q : Load bearing piston in a certain hydraulic....
    Mechanical Engineering :

    The load bearing piston in a certain hydraulic has an area 50 times as large as the input piston. If the larger piston supports a load of 6000N, how large a force must be applied to the input system

  • Q : What is the thermal efficiency of the engine....
    Mechanical Engineering :

    A diesel engine performs 2090 J of mechanical work and discards 4125 J of heat each cycle. What is the thermal efficiency of the engine?

  • Q : Fluids mechanics....
    Mechanical Engineering :

    Fluids mechanics, Fluid mechanics boundary layer theory...................................................................

  • Q : Determine the rms current in the circuit....
    Electrical Engineering :

    An ac generator with a frequency of 150Hz and an rms voltage of 22.5V is connected in series with a 15.0 kilo ohms resistor and a 0.210microF capacitor. What is the rms current in this circuit?

  • Q : Rms current in an ac circuit....
    Electrical Engineering :

    The rms current in an ac circuit with a resistance of 100ohms is 0.85A . What is the average power consumed by this circuit?

  • Q : Calculate the electric flux through the hole....
    Electrical Engineering :

    An uncharged nonconductive hollow sphere of radius16.0cm surrounds a17.0µC charge located at the origin of a cartesian coordinate system. A drill with a radius of 1.00 mm is aligned along thez

  • Q : Electrical conductor designed to carry large currents....
    Electrical Engineering :

    An electrical conductor designed to carry large currents has a circular cross section 2.50 mm in diameter and is 14.0 m long. The resistance between its ends is 0.104 n.

  • Q : What is the average force between foot and the ball....
    Mechanical Engineering :

    Tom kicks the ball with a speed of 5m/s horizontally and Jim kicks it back to Tom with a speed of 9m/s. If the contact time between Jim's foot and the ball is 0.003s, what is the average force betwee

  • Q : What kind of wrench should you look for loosen a bolt....
    Mechanical Engineering :

    You are trying to loosen a bolt from a piece of metal with a wrench but fail. What kind of wrench should you look for? one made out of wood or plastic.

  • Q : How long it take the motor to make one revolution....
    Mechanical Engineering :

    A typical bacterial motor turning at a constant angular velocity has a radius of 1.28 10-8 m, and a tangential speed at the rim of 2.24 10-5 m/s. How long does it take the motor to make one revolu

  • Q : Find a formula for the inverse function....
    Engineering Mathematics :

    The formula C = 5/9 (F - 32), where F > - 459.67, expresses the Celsius temperature C as a function of the Fahrenheit temperature F. Find a formula for the inverse function and interpret it. What i

  • Q : Ratio of low temperature-high temperature in carnot engine....
    Mechanical Engineering :

    If the efficiency of this engine is 58% of the efficiency of a Carnot engine, what is the ratio of the low temperature to the high temperature in the Carnot engine?

  • Q : What is the rise in temperature of the flowing water....
    Mechanical Engineering :

    If excess energy is carried away from the plant by a river with a flow rate of 1.0 multiplied by 106 kg/s, what is the rise in temperature of the flowing water?

  • Q : Lagranges mean value theorem....
    Engineering Mathematics :

    Use Lagrange's Mean Value Theorem to determine a point on the curve y = vx/2 where the tangent is parallel to the chord joining (2, 0) and (3, 1)

  • Q : What torque motor supply take disk from one rpm to another....
    Mechanical Engineering :

    A 250 g , 23.0-cm-diameter plastic disk is spun on an axle through its center by an electric motor. What torque must the motor supply to take the disk from 0 to 2000 rpm in 4.50s?

  • Q : What is the maximum possible efficiency of the engine....
    Mechanical Engineering :

    The collectors deliver aeat at 70 degrees C and the engine releases heat to the surroundings at 35 degrees C. What is the maximum possible efficiency of this engine?

  • Q : How much heat engine takes from higher remperature reservior....
    Mechanical Engineering :

    A Carnot engine operates between temperatures of 700K and 400K and does 150 J of work in each cycle. What is the efficiency? How much heat does it take from the higher remperature reservior in each cy

  • Q : How much work per cycle is required to operate refrigerator....
    Mechanical Engineering :

    In each cycle of its operation, a refrigerator removes 17J of heat from the inside of the refrigerator and releases 40J of heat into the room. How much work per cycle is required to operate this

  • Q : What is the mechanical power output of engine....
    Mechanical Engineering :

    A heat engine operates in a Carnot cycle between72.0°C and345°C. It absorbs 21,600J of energy per cycle from the hot reservoir. The duration of each cycle is5.00s. What is the mechanical pow

  • Q : What is the turns ratio of a transformer....
    Electrical Engineering :

    For safety, medical equipment connected to patients is often powered by an isolation transformer, whose primary is connected to 120-V AC power and whose secondary delivers 120-V power.

  • Q : Hi i need your help....
    Mechanical Engineering :

    Hi i need your help, hi i study in university in greece...i need your help until tomorrow for a mechanical draw.. I must draw the front view and right view and the down-view. The draw is below.. can

  • Q : Feedback control system (7)....
    Electrical Engineering :

    Feedback control system (7), CAN YOU SOLVE THE ATTACHED FILE ITS ONLY ONE QUESTION AM EXPECTING GOOD PRICE ON IT... THANKS...

  • Q : What beat frequency will be measured by the student....
    Mechanical Engineering :

    A student plays two notes on the piano keyboard simultaneously. The white key has a frequency of 352 Hz and the black key has a frequency of 373. What beat frequency will be measured by the student?

  • Q : Problem based on railroad switchyard....
    Mechanical Engineering :

    In a railroad switchyard, a 50 ton freight car is sent at 7.4 mi/h toward a 27 ton car that is moving in the same direction at 2.0 mi/h.

  • Q : What wavelength of visible light absent in reflected light....
    Mechanical Engineering :

    A soap bubble with walls 398 thick floats in air. If this bubble is illuminated perpendicularly with sunlight, what wavelength of visible light will be absent in the reflected light? Assume that the

©TutorsGlobe All rights reserved 2022-2023.