Find velocity of molten metal at the base of sprue, Mechanical Engineering

+44 141 628 6080
[email protected]

Find velocity of molten metal at the base of sprue

A downsprue of a certain mold has a length of 175 mm and a cross-sectional area at the base of 400 mm2. The runner has the same area and is of circular cross section. The mold cavity has a volume of 0.001 m3. Density is 2700 kg/m3 and viscosity is .0015 Pa s. Determine: the velocity of the molten metal at the base of the sprue, the volume flow rate, the time required to fill the mold, the Reynolds number in the runner, and whether or not the flow in the runner is turbulent.

View Complete Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Find velocity of molten metal at the base of sprue

Reference No:- TGS0834128

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Find the minimum sample size needed

Find the minimum sample size needed, using a prior study that found that 25% of the respondents said they support abolishing the penny. (Round to the nearest whole number)

Q : Problem related to position of maximum electric flux

A 40.0 cm diameter circular loop is rotated in a uniform electric field until the position of maximum electric flux is found. The flux in this position is measured to be 5.20*10^5 N*m/C. What is the magnitude of the electric field?

Q : Normal distribution of sat critical

Use the normal distribution of SAT critical reading scores for which the mean is 511 and the standard deviation is 115. Assume the variable x is normally distributed.

Q : What would be the equivalent capacitance

Two capacitors C1 and C2 are connected in series to a 9V battery. The magnitude of the charge on each plate of C1 is 7.5μC. The value of C1 is 2μF. What would be the equivalent capacitance if the two capacitors were wired in parallel?

Q : Find velocity of molten metal at the base of sprue

Determine: the velocity of the molten metal at the base of the sprue, the volume flow rate, the time required to fill the mold, the Reynolds number in the runner, and whether or not the flow in the runner is turbulent.

Q : Log is pulled up a ramp by means of a rope based problem

A 296 kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 30.0° with respect to the horizontal.

Q : Standardized test for high school students

In a recent year, scores on a standardized test for high school students with a 3.50 to 4.00 grade point average were normally distributed, with a mean of 38.7 and a standard deviation of 1.6.

Q : What is the speed of electrons in the beam

The electrons in the beam were accelerated by a voltage of 3.0 kV; the beam was then steered to different points on the screen by coils of wire that produced a magnetic field of up to 0.50 T. What is the speed of electrons in the beam?

Q : How much power does it take to move the plate

Consider two flat circular plates (6 inch diameter), with honey filling a 0.05 inch gap between them. If it takes 1 lbf to start sliding the plates apart at 0.25 inches/sec, what is the viscosity of the honey?

1950345

Questions
Asked

3,689

Active Tutors

1412852

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Find velocity of molten metal at the base of sprue

Reference No:- TGS0834128

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Find the minimum sample size needed

Q : Problem related to position of maximum electric flux

Q : Normal distribution of sat critical

Q : What would be the equivalent capacitance

Q : Find velocity of molten metal at the base of sprue

Q : Log is pulled up a ramp by means of a rope based problem

Q : Standardized test for high school students

Q : What is the speed of electrons in the beam

Q : How much power does it take to move the plate

Areas mentioned specifically as wanting to join the eeu

Compare independent variables, dependent variables

How level of parental involvement impact middle school

Describe psychology research methods

Searching for articles relating to young people

You stay late at work to finish an important report

What options is true in relation to validity

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Find velocity of molten metal at the base of sprue

Reference No:- TGS0834128

Recent Questions Asked Mechanical Engineering

Q : Find the minimum sample size needed

Q : Problem related to position of maximum electric flux

Q : Normal distribution of sat critical

Q : What would be the equivalent capacitance

Q : Find velocity of molten metal at the base of sprue

Q : Log is pulled up a ramp by means of a rope based problem

Q : Standardized test for high school students

Q : What is the speed of electrons in the beam

Q : How much power does it take to move the plate

Asked Questions