Estimate the average temperature of the plate, Mechanical Engineering

+44 141 628 6080
[email protected]

Estimate the average temperature of the plate

A blackened plate is exposed to the sun so that a constant heat flux of 800 W/m^2 is absorbed. The back side of the plate is insulated so that all the absorbed energy is dissipated into the airstream. Air blows across the plate at a temperature of 25 degrees C and 3m/s. The plate is 25cm square. Estimate the average temperature of the plate.

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Estimate the average temperature of the plate

Reference No:- TGS0739297

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Delivers appliances for a large retail operation

A trucking firm delivers appliances for a large retail operation. The packages (or crates) have a mean weight of 305 lb. and a variance of 2916. (Give your answers correct to four decimal places.)

Q : Determine the maximum rate of heat removal from refrigereted

A Carnot heat engine receives heat from a reservoir at 900 degrees Celsius at a rate of 800kJ/min and rejects the waste heat to the ambient air at 27 degrees Celsius.

Q : Amount of heat as a refrigerator

How long would a 2.90 kW space heater have to run to put into a kitchen the same amount of heat as a refrigerator (coefficient of performance = 2.68) does when it freezes 1.73 kg of water at 18.8°C into ice at 0°C?

Q : Find required volume of cuts using average-end-area method

Determine the required volume of the cuts and fills for a new road, using the average-end-area-method.

Q : Estimate the average temperature of the plate

Q : Determine amount of excavation needed for the basement

Determine the amount of excavation needed for the basement. A 2 foot working distance is required and the excavation will be sloped 1.5:1.

Q : Spring clamped to the table shoots

In a physics lab experiment, a spring clamped to the table shoots a 19g ball horizontally. When the spring is compressed 21cm , the ball travels horizontally 5.0m and lands on the floor 1.6m below the point at which it left the spring.

Q : What is the heat gain per unit length of the duct

If the horizontal duct is uninsulated and exposed to air at 35 C in the crawl space beneath a home, what is the heat gain per unit length of the duct?

Q : By what percent does the kinetic energy decrease

Tennis balls, to be acceptable for tournament play, must have a mass of 57.5 g. When dropped from a height of 2.5 m onto a concrete surface, a ball must rebound to a height of 1.4 m. During impact, the ball compresses by approximately 6 mm. By wha

1957373

Questions
Asked

3,689

Active Tutors

1456621

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Estimate the average temperature of the plate

Reference No:- TGS0739297

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Delivers appliances for a large retail operation

Q : Determine the maximum rate of heat removal from refrigereted

Q : Amount of heat as a refrigerator

Q : Find required volume of cuts using average-end-area method

Q : Estimate the average temperature of the plate

Q : Determine amount of excavation needed for the basement

Q : Spring clamped to the table shoots

Q : What is the heat gain per unit length of the duct

Q : By what percent does the kinetic energy decrease

Considering nasotracheal suctioning to clear patient airway

Describe socrative solutions for each learner group

Identify one or two nurses on your unit

Describe psychiatric clinic by her primary provider

Escribe assessment you need to do for the epidural patient

What is the cause of this metabolic state

Express concern about an abnormal lab value report

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Estimate the average temperature of the plate

Reference No:- TGS0739297

Recent Questions Asked Mechanical Engineering

Q : Delivers appliances for a large retail operation

Q : Determine the maximum rate of heat removal from refrigereted

Q : Amount of heat as a refrigerator

Q : Find required volume of cuts using average-end-area method

Q : Estimate the average temperature of the plate

Q : Determine amount of excavation needed for the basement

Q : Spring clamped to the table shoots

Q : What is the heat gain per unit length of the duct

Q : By what percent does the kinetic energy decrease

Asked Questions