Discuss the tensile capacity of the angle, Mechanical Engineering

+44 141 628 6080
[email protected]

Discuss the tensile capacity of the angle

1. For the connection shown in figure, assuming the bolts are ¾- in. diameter and the angle and plate ASTM A36 determine:
(a) Tensile capacity of the angle
(b) Required gusset plate and thickness for the tensile capacity of angle obtained in part a above. Take the yield strength as 36 ksi. and ultimate strength as 58 ksi.

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Discuss the tensile capacity of the angle

Reference No:- TGS0734850

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : What percent increase in tension is needed to tune

Assuming the piano strong has too low a pitch, what percent increase in tension is needed to bring the string into tune? You answer should be given to the nearest tenth of a percent.

Q : Find the time taken for the liquid level in the tank to fall

The storage tank of a water tower is a vertical cylinder of diameter D = 7 m, the initial depth of water within it is ho =6 m and the free surface is exposed to the atmosphere.

Q : What is the value of the reflecting finesse

Find the maximum and minimum transmittance of the interferometer? What is the value of the reflecting finesse and of the coefficient of finesse ?

Q : Sketch the variation of shear stress vs shear strain

Sketch (not to scale) the variation of shear stress vs shear strain along the radius in a composite bar of total radius R whose inner material of radius 'ri' has a shear modulus greater than the outer material.

Q : Discuss the tensile capacity of the angle

Required gusset plate and thickness for the tensile capacity of angle obtained in part a above. Take the yield strength as 36 ksi. and ultimate strength as 58 ksi.

Q : Events a and b with the probabilities

An experiment can result in one or both of events A and B with the probabilities events A and B with the probabilities shown in this probability table:

Q : Percentage of accounting firms

At a 1% level of significance, does your test show enough evidence to conclude that a significantly lower percentage of accounting firms offer employees flexible scheduling? What is the p-value for this test?

Q : How much heat has been added when only saturated vapor

A 1m^3 rigid tank initially contains 5*kg of steam at 150degC. A relief valve on top of the tank is opened to allow steam to slowly escape the tank. Heat is added to the water in the tank to maintain the temperature at 150degC.

Q : Consequences of making a type ii error

What are the consequences of making a type II error? What is the probability of making a Type II error if the true population mean is 695 hours?

1925440

Questions
Asked

3,689

Active Tutors

1416421

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Discuss the tensile capacity of the angle

Reference No:- TGS0734850

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : What percent increase in tension is needed to tune

Q : Find the time taken for the liquid level in the tank to fall

Q : What is the value of the reflecting finesse

Q : Sketch the variation of shear stress vs shear strain

Q : Discuss the tensile capacity of the angle

Q : Events a and b with the probabilities

Q : Percentage of accounting firms

Q : How much heat has been added when only saturated vapor

Q : Consequences of making a type ii error

Discussion about the nature versus nurture

Is lifespan psychologists are unlikely to investigate

How teenagers in an impoverished urban area spend their time

Why you feel unpleasantly hot and sweaty

Describe the results, including any scores

Problem on journal articles and non-journal materials

Outline a social issue that is important to you

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Discuss the tensile capacity of the angle

Reference No:- TGS0734850

Recent Questions Asked Mechanical Engineering

Q : What percent increase in tension is needed to tune

Q : Find the time taken for the liquid level in the tank to fall

Q : What is the value of the reflecting finesse

Q : Sketch the variation of shear stress vs shear strain

Q : Discuss the tensile capacity of the angle

Q : Events a and b with the probabilities

Q : Percentage of accounting firms

Q : How much heat has been added when only saturated vapor

Q : Consequences of making a type ii error

Asked Questions