Determine the flow rate and the temperature of the hot water, Mechanical Engineering

+44 141 628 6080
[email protected]

Determine the flow rate and the temperature of the hot water

Wet steam (P=12.8 kPa, x=0.90 ) enters a heat exchanger with a flow rate of 1.2 kg/s. cold water at 12.8 kPa and K also enters the exchanger with a flow rate of 30 kg/s. the seam and the water mix adiabatically at constant pressure within the heat exchange. A single stream exits. Determine the flow rate and the temperature of the hot water exiting the heat exchanger

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine the flow rate and the temperature of the hot water

Reference No:- TGS0737561

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Find the mass flow rates of the exiting liquid

A flow of 2 kg/s of saturated liquid R-134a at 200 kPa is mixed with 3 kg/s of R-134a at 200 kPa and 10?C. The liquid and vapor phases of the mixture are separated, and each exit separately at 200 kPa.

Q : Explain required mass flow rate of air through the turbine

The inlet state is 60 PSI, 102 F, and the exit state is 14.7 PSI, -20 F, assuming the velocities to be low and the process to be adiabatic, find the required mass flow rate of air through the turbine.

Q : What is the temperature as it leaves the valve assuming

Water flowing in a line at 60 lbf/in2, saturated vapor is taken out through a valve at 14.7 lbf/in2. What is the temperature as it leaves the valve assuming no changes in kinetic energy and no heat transfer?

Q : Determine the final temperature and mass inside the tank

A 1-ft3 tank that is initially evacuated is connected by a valve to an air supply line flowing air at 70oF, 120 psi. The valve is opened, and air flows into the tank until the pressure reaches 90 psi.

Q : Determine the flow rate and the temperature of the hot water

Q : Find boundary layer thickness inches from leading edge

You know that the fin is 1.3 ft in length and the cruising speed of a stingray is 25 km/hr. What is the boundary layer thickness 6 inches from the leading edge of the fin?

Q : What was the diameter at ambient conditions

If the Pu was in the shape of a cylinder with equal diameter (d) and length (L), what was the diameter (in cm) at ambient conditions?

Q : What strain is needed to obtain this density

If the Pu needs to be compressed to 25g/cm^3 to explode, what strain is needed to obtain this density? [strain = (delta Length)/Length)]?

Q : Determine the amount of work transfer from the air

A spherical balloon is inflated from a diameter of 10 cm to a diameter of 20 cm by forcing air into the balloon with a tire pump. The initial pressure inside the balloon is 150 kPa. During the process the pressure is proportional to the balloon di

1928486

Questions
Asked

3,689

Active Tutors

1421688

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine the flow rate and the temperature of the hot water

Reference No:- TGS0737561

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Find the mass flow rates of the exiting liquid

Q : Explain required mass flow rate of air through the turbine

Q : What is the temperature as it leaves the valve assuming

Q : Determine the final temperature and mass inside the tank

Q : Determine the flow rate and the temperature of the hot water

Q : Find boundary layer thickness inches from leading edge

Q : What was the diameter at ambient conditions

Q : What strain is needed to obtain this density

Q : Determine the amount of work transfer from the air

Cases of local communities using modern technology

Discussion about idea of the tramp stamp

Symbolic interactionism took off as a theoretical approach

How sociological models help understand mental illness

What cases does female status tend to be highest

Why does victor coin the term hyper-violence

Which are forms of media bias

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Determine the flow rate and the temperature of the hot water

Reference No:- TGS0737561

Recent Questions Asked Mechanical Engineering

Q : Find the mass flow rates of the exiting liquid

Q : Explain required mass flow rate of air through the turbine

Q : What is the temperature as it leaves the valve assuming

Q : Determine the final temperature and mass inside the tank

Q : Determine the flow rate and the temperature of the hot water

Q : Find boundary layer thickness inches from leading edge

Q : What was the diameter at ambient conditions

Q : What strain is needed to obtain this density

Q : Determine the amount of work transfer from the air

Asked Questions