Calculate the factor of safety the designer must have used, Mechanical Engineering

+44 141 628 6080
[email protected]

Calculate the factor of safety the designer must have used

A small 6-mm diameter pin was designed using ASTM no. 40 cast iron to withstand an axial compressive load of 3.5kN combined with a torsional load of 9.8 N.m. Calculate the factor of safety the designer must have used. The elongation in a 2-in speciman of ASTN No. 40 at failure is approximately 0.5%-1.0%. (Use all applicable theories)

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Calculate the factor of safety the designer must have used

Reference No:- TGS0738681

Expected delivery within 24 Hours

Have a Question? (oR Write a Review)

Write atleast 100 words!!

Recent Questions Asked Mechanical Engineering

Q : Discuss the allowed range of mass flow rates for the water

Oil Enters a counterflow heat exchanger at 450k with a mass flow rate of 10 kg/s and exits at 350k. A seperate stream of liquid water enters at 20 C, 5 bar.

Q : What was its initial velocity

A golfer hits a ball , giving it a maximum height of 20 m . If the ball lands 130 m away at the level from which he hit it, what was its initial velocity?(neglect air resistance)

Q : How much extra charge will flow from the battery

If a dielectric material with kappa=3.60 is inserted so that it fills the volume between the plates (with the capacitor still connected to the battery), how much additional charge will flow from the battery onto the positive plate?

Q : Compute number of kilograms of hydrogen that pass per hour

Calculate the number of kilograms of hydrogen that pass per hour through a 6.0-mm-thick sheet of palladium having an area of 0.40 m2 at 500°C.

Q : Calculate the factor of safety the designer must have used

Calculate the factor of safety the designer must have used. The elongation in a 2-in speciman of ASTN No. 40 at failure is approximately 0.5%-1.0%.

Q : Is there any heat loss from the steam turbine

The steam at the inlet is 20 bar absolute with superheat of 135 C . The steam at the outlet is 1 bar absolute and 100 C. The velocity of the steam at inlet is 3m/s, and 12 m/s at the outlet.

Q : What is the maximum heating rate for nucleate boiling

Saturated water at 1 atm and velocity 2 m/s flows over a cylindeical heating element of diameter 5 mm. What is the maximum heating rate (W/m) for nucleate boiling?

Q : Find if component is safe for design factor at two points

A component is made of a brittle material that has prperties Sut=30 ksi and Suc= 90ksi. Use MNST, BCMT, MMT to determine if the component is safe for a design factor 1.5 at two points.

Q : Determine the thickness of steel plate required

Determine the thickness of steel plate required for a 2m diameter cylindrical boiler with hemispherical ends if the tensile and shear stresses in the plate are not to exceed 85 Mpa and 40 Mpa.

1955606

Questions
Asked

3,689

Active Tutors

1419170

Questions
Answered

Start Excelling in your courses, Ask a tutor for help and get answers for your problems !!

ask Question

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Calculate the factor of safety the designer must have used

Reference No:- TGS0738681

Have a Question? (oR Write a Review)

Recent Questions Asked Mechanical Engineering

Q : Discuss the allowed range of mass flow rates for the water

Q : What was its initial velocity

Q : How much extra charge will flow from the battery

Q : Compute number of kilograms of hydrogen that pass per hour

Q : Calculate the factor of safety the designer must have used

Q : Is there any heat loss from the steam turbine

Q : What is the maximum heating rate for nucleate boiling

Q : Find if component is safe for design factor at two points

Q : Determine the thickness of steel plate required

How sociological models help understand mental illness

Which are forms of media bias

Problem regarding culturally relativistic

Discussion about cultural appropriation

Statement about political systems controlled by men

How the major schools of thought within sociology

How are schools important in the struggle for power

Request for Solution File

Ask an Expert for Answer!!

Mechanical Engineering: Calculate the factor of safety the designer must have used

Reference No:- TGS0738681

Recent Questions Asked Mechanical Engineering

Q : Discuss the allowed range of mass flow rates for the water

Q : What was its initial velocity

Q : How much extra charge will flow from the battery

Q : Compute number of kilograms of hydrogen that pass per hour

Q : Calculate the factor of safety the designer must have used

Q : Is there any heat loss from the steam turbine

Q : What is the maximum heating rate for nucleate boiling

Q : Find if component is safe for design factor at two points

Q : Determine the thickness of steel plate required

Asked Questions